The model CS shear has the same hydra-mechanical,
guillotine straight line cutting
action drive system
The guillotine system is by far the most preferred method used by precision manufacturers
of shears. This system provides the most accurate cutting action due to the
fact that the blade comes straight down to shear the workpiece. The travel
of the upper blade from the top of the travel to the bottom is a straight line through
the entire cut and the angle between the two blades never changes. Virtually
all of the quality U.S. made shears manufactured in this century have been of the
guillotine design. The guillotine system uses ram slides (gibbs) which guide the
upper beam and solidly contain the shearing forces. Our ram slides are located directly
above the shearing area on the front and back of the shear ram above the shearing
center line. In this design, as used by Standard Industrial, the ram is completely
contained in the slides throughout the entire ram travel.
as the AS, as well as the 5 year parts
and limited labor warranty. Like the AS, the
CS also comes standard with our 36” travel, PLC controlled backgauge with “Go-To” and
multi-level programming. The main difference between the AS and the CS is that
the CS is only available in the ¼” and 3/8” x 10’ and 12’ capacities and it is
only available with a limited amount of options, whereas the AS is available in many
lengths and capacities and has a wider variety of options to choose from. |
In addition to the model AS shear, we now
offer an economical model CS shear in ¼” x 10’ and ¼” x 12’ and 3/8” x 10’ and 3/8”
x 12’ capacities. The CS is an extremely affordable version of the model AS shear
that we have been making for over 30 years.
The incredibly simple, quick change manual blade gap adjustment provides a positive
mechanical adjustment via precision machined tapered gibbs |
Model CS250-10 (1/4” x 10’ capacity) shear shown with all standard features and 5 year
parts warranty. |
| An advantage of the CS is that it comes standard with many
features that the AS does not come with. Like the
AS, the CS comes standard with an extremely heavy duty frame; Industrial quality electrics;
80,000 P.S.I. steel capacity, and the same high quality, readily available components.
Unlike the AS however, the CS also comes standard with a manual quick change blade gap
adjustment; a quantity of (2) hand slots and (2) t-slots in the shear table; a 4’ squaring
arm with imbedded scale and an impressive list of other standard features (see below).
With a long list of other impressive options and standard features, the Standard Industrial
shear will make you proud when you say that you “bought American. |
|
Optionally, the CS can be equipped with a longer squaring arm; 24” t-slot support
arms; swing stops for the squaring arm; gravity stops for the t-slots; protractors;
impact pads for the hold down cylinders, higher carbon blades and conveying, stacking
and sheet support systems.
|
| (2) hand slots—(2) T-slots—4’ Squaring arm with scale—Pendant
mounted PLC control for 36” travel Go-To backgauge are all standard features on the
CS model shears |
| The CS series shear is perfect for any customer who is looking for a
100% U.S. Made ¼” or 3/8” x 10’ shear at a very affordable price, while not requiring
a substantial amount of customization. As with all Standard Industrial machinery,
we stand behind our model CS shears with our unmatched
5 Year parts and limited labor warranty. |
 |
|
STANDARD FEATURES
|
| 5 Year parts and limited
labor warranty |
Unitized high strength frame |
|
100% Made In The U.S.A.
|
Overload protection |
|
80,000 P.S.I. steel capacity
|
Blade relief angle
|
|
High quality chrome shock resistant four edge blades
|
Standards to meet OSHA and ANSI B11.4 specifications
|
|
3 position, hooded and latched safety type footswitch
|
Complete hydraulics with filter and oil in the reservoir
|
|
High tonnage hydraulic hold down cylinders
|
Shock-less quite operation
|
|
Shadow light for cutting to a line
|
120 volt electrical control system
|
|
(2) T-slots machined in the table
|
Clear area under backgauge
|
|
(2) Hand slots machined in the table
|
Low maintenance, extremely heavy duty design
|
|
Low friction, low maintenance NSM bearings that require very limited lubrication
|
Guillotine straight line cutting action designed for 80,000 PSI steel
|
| High strength chromed shafts in the guillotine drive system |
Adjustable hold down tonnage for sensitive material
|
| 4 ‘ squaring arm with imbedded scale (4’ total length from blade) |
Easy to use controls |
| Extremely heavy duty, 36” travel, PLC controlled backgauge
with Go-To and multi-level programming, operator password protection and many other
features |
|
Rear view of a Standard shear with optional power swing-away backgauge, this power swingaway
backgauge comes with 48” of travel and instantly pulls the entire backgauge up and out of the
way. The Standard Industrial backgauge is the most heavy duty unit available on the market
today.
|
|
|
|
Extremely heavy duty 36” travel, PLC controlled backgauge with "go-To" control and multi-level
programming.
|
|
|
|
Manual swingaway backstop for shearing pieces longer than the travel of the backgauge.
|
|
|
|
Clear area under backgauge for stacking/conveying equipment.
|
|
|
|
Rear backgauge shaft is fitted with couplings to allow end to end adjustment of the backstop.
|
|
|
|
|
|
|
|
The heavy duty backgauge consists of gear reducers to provide power to high quality, precise
lead screws which power the traverse assemblies. These assemblies are carried on heavy
roller bearings which require no lubrication and have no sliding friction. All bearings
and gears are readily available from your local vendor.
|
|
|
|
|
Complete control of all operations located on front of shear.
|
|
|
|
Digital display showing precise location of backstop in inches or millimeters.
|
|
|
|
Overload protection to prevent damage to machine.
|
|
|
|
Meets J.I.C. standards with liquid tight enclosures and magnetic starter.
|
|
|
|
Inch mode allows complete ram control throughout stroke.
|
|
